--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/libs/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/readme.txt	Mon Oct 03 21:19:15 2011 +1030
@@ -0,0 +1,87 @@
+/**
+  @page DMA_FLASH_RAM DMA FLASH to RAM example
+  
+  @verbatim
+  ******************** (C) COPYRIGHT 2011 STMicroelectronics *******************
+  * @file    DMA/FLASH_RAM/readme.txt 
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    08-April-2011
+  * @brief   Description of the DMA FLASH to RAM example.
+  ******************************************************************************
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  ******************************************************************************
+   @endverbatim
+
+@par Example Description 
+
+This example provides a description of how to use a DMA channel to transfer 
+a word data buffer from FLASH memory to embedded SRAM memory.
+
+DMA1 Channel6 is configured to transfer the contents of a 32-word data buffer
+stored in Flash memory to the reception buffer declared in RAM.
+
+The start of transfer is triggered by software. DMA1 Channel6 memory-to-memory
+transfer is enabled. Source and destination addresses incrementing is also enabled.
+The transfer is started by setting the Channel enable bit for DMA1 Channel6.
+At the end of the transfer a Transfer Complete interrupt is generated since it
+is enabled. Once interrupt is generated, the remaining data to be transferred is
+read which must be equal to 0. The Transfer Complete Interrupt pending bit is
+then cleared. A comparison between the source and destination buffers is done to
+check that all data have been correctly transferred.
+
+
+@par Directory contents 
+
+  - DMA/FLASH_RAM/stm32f10x_conf.h    Library Configuration file
+  - DMA/FLASH_RAM/stm32f10x_it.c      Interrupt handlers
+  - DMA/FLASH_RAM/stm32f10x_it.h      Interrupt handlers header file
+  - DMA/FLASH_RAM/main.c              Main program
+  - DMA/FLASH_RAM/system_stm32f10x.c  STM32F10x system source file
+
+@par Hardware and Software environment 
+
+  - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density, 
+    XL-Density,High-Density Value line, Medium-Density Value line, Low-Density 
+    and Low-Density Value line Devices.
+  
+  - This example has been tested with STMicroelectronics STM32100B-EVAL (Medium-Density
+    Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density 
+    and XL-Density), STM32100E-EVAL (High-Density Value line) and STM3210B-EVAL 
+    (Medium-Density) evaluation boards and can be easily tailored to any other 
+    supported device and development board.
+
+
+@par How to use it ? 
+
+In order to make the program work, you must do the following :
+ - Copy all source files from this example folder to the template folder under
+   Project\STM32F10x_StdPeriph_Template
+ - Open your preferred toolchain 
+ - Rebuild all files and load your image into target memory
+ - Run the example 
+
+@note
+ - Low-density Value line devices are STM32F100xx microcontrollers where the 
+   Flash memory density ranges between 16 and 32 Kbytes.
+ - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
+ - Medium-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 64 and 128 Kbytes.  
+ - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
+ - High-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.
+ - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.
+ - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 512 and 1024 Kbytes.
+ - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
+   
+ * <h3><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h3>
+ */