Mercurial > ~darius > hgwebdir.cgi > stm32temp
view libs/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DAC/OneChannel_NoiseWave/readme.txt @ 8:58d76cf522ff
Split out code into separate files.
author | Daniel O'Connor <darius@dons.net.au> |
---|---|
date | Sat, 04 Feb 2012 13:29:31 +1030 |
parents | c59513fd84fb |
children |
line wrap: on
line source
/** @page DAC_OneChannel_NoiseWave DAC one channel noise wave example @verbatim ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* * @file DAC/OneChannel_NoiseWave/readme.txt * @author MCD Application Team * @version V3.5.0 * @date 08-April-2011 * @brief Description of the DAC one channel noise wave example. ****************************************************************************** * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. ****************************************************************************** @endverbatim @par Example Description This example describes how to use one DAC channel to generate a signal with noise waves on DAC Channel1 output. DAC channel1 conversion are configured to be triggered by software with noise wave generation.12bit left data alignment is selected since we choose to access DAC_DHR12L1 register. Bits 0 to 8 are masked for the Linear feedback shift register. DAC channel1 is then enabled. DAC Channel1 DHR12L1 register is configured to have an output voltage of VREF/2. Software triggers are generated continuously in an infinite loop, and on each trigger the DAC channel1 start the conversion and calculate the noise value to apply on the DAC channel1 output. The output signal with noise waves can be visualized by connecting PA.04 pin to an oscilloscope. @par Directory contents - DAC/OneChannel_NoiseWave/stm32f10x_conf.h Library Configuration file - DAC/OneChannel_NoiseWave/stm32f10x_it.c Interrupt handlers - DAC/OneChannel_NoiseWave/stm32f10x_it.h Header for stm32f10x_it.c - DAC/OneChannel_NoiseWave/main.c Main program - DAC/OneChannel_NoiseWave/system_stm32f10x.c STM32F10x system source file @par Hardware and Software environment - This example runs on STM32F10x Connectivity line, High-Density, XL-Density, High-Density Value line, Medium-Density Value line and Low-Density Value line Devices. - This example has been tested with STMicroelectronics STM32100B-EVAL (Medium-Density Value line),STM32100E-EVAL (High-Density Value line), STM3210C-EVAL (Connectivity line) and STM3210E-EVAL (High-Density and XL-Density) evaluation boards and can be easily tailored to any other supported device and development board. - STM32100B-EVAL Set-up - Connect PA.04 pin to an oscilloscope @note JP2 should be open - STM3210C-EVAL Set-up - Connect PA.04 pin to an oscilloscope - STM3210E-EVAL Set-up - Connect PA.04 pin to an oscilloscope - STM32100E-EVAL Set-up - Connect PA.04 pin to an oscilloscope @par How to use it ? In order to make the program work, you must do the following : - Copy all source files from this example folder to the template folder under Project\STM32F10x_StdPeriph_Template - Open your preferred toolchain - Rebuild all files and load your image into target memory - Run the example @note - Low-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. - Medium-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. - High-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 256 and 512 Kbytes. - High-density devices are STM32F101xx and STM32F103xx microcontrollers where the Flash memory density ranges between 256 and 512 Kbytes. - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where the Flash memory density ranges between 512 and 1024 Kbytes. - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. * <h3><center>© COPYRIGHT 2011 STMicroelectronics</center></h3> */