--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/libs/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/TIM/OCActive/readme.txt	Mon Oct 03 21:19:15 2011 +1030
@@ -0,0 +1,123 @@
+/**
+  @page TIM_OCActive TIM OC Active example
+  
+  @verbatim
+  ******************** (C) COPYRIGHT 2011 STMicroelectronics *******************
+  * @file    TIM/OCActive/readme.txt 
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    08-April-2011
+  * @brief   Description of the TIM OC Active example.
+  ******************************************************************************
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  ******************************************************************************
+   @endverbatim
+
+@par Example Description 
+
+This example shows how to configure the TIM peripheral to generate four different 
+signals with four different delays.
+
+The TIM3CLK frequency is set to SystemCoreClock / 2 (Hz), and the objective is
+to get TIM3 counter clock at 1 KHz so the Prescaler is computed as following:
+   - Prescaler = (TIM3CLK / TIM3 counter clock) - 1
+SystemCoreClock is set to 72 MHz for Low-density, Medium-density, High-density
+and Connectivity line devices and to 24 MHz for Low-Density Value line,
+Medium-Density Value line and High-Density Value line devices.
+
+The TIM3 CCR1 register value is equal to 1000:
+TIM3_CH1 delay = CCR1_Val/TIM3 counter clock  = 1000 ms
+so the TIM3 Channel 1 generates a signal with a delay equal to 1000 ms.
+
+The TIM3 CCR2 register value is equal to 500:
+TIM3_CH2 delay = CCR2_Val/TIM3 counter clock = 500 ms
+so the TIM3 Channel 2 generates a signal with a delay equal to 500 ms.
+
+The TIM3 CCR3 register value is equal to 250:
+TIM3_CH3 delay = CCR3_Val/TIM3 counter clock = 250 ms
+so the TIM3 Channel 3 generates a signal with a delay equal to 250 ms.
+
+The TIM3 CCR4 register value is equal to 125:
+TIM3_CH4 delay = CCR4_Val/TIM3 counter clock = 125 ms
+so the TIM3 Channel 4 generates a signal with a delay equal to 125 ms.
+
+The delay correspond to the time difference between PC.06 and 
+TIM3_CHx signal rising edges in case of STM32100E-EVAL, STM32100B-EVAL, STM3210E-EVAL 
+and STM3210B-EVAL 
+
+The delay correspond to the time difference between PD.07 and 
+TIM3_CHx signal rising edges in case of STM3210C-EVAL
+
+@par Directory contents 
+
+  - TIM/OCActive/stm32f10x_conf.h    Library Configuration file
+  - TIM/OCActive/stm32f10x_it.c      Interrupt handlers
+  - TIM/OCActive/stm32f10x_it.h      Interrupt handlers header file
+  - TIM/OCActive/main.c              Main program 
+  - TIM/OCActive/system_stm32f10x.c  STM32F10x system source file
+  
+@par Hardware and Software environment 
+
+
+  - This example runs on STM32F10x Connectivity line, High-Density, High-Density 
+    Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density 
+    and Low-Density Value line Devices.
+  
+  - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density
+    Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), 
+    STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) 
+    evaluation boards and can be easily tailored to any other supported device 
+    and development board.
+    
+
+  - STM3210C-EVAL Set-up 
+    - Connect the TIM3 pins(TIM3 full remapped pins) to an oscilloscope to
+      monitor the different waveforms:
+       - PD.07
+       - PC.06 (TIM3_CH1)
+       - PC.07 (TIM3_CH2)
+       - PC.08 (TIM3_CH3)
+       - PC.09 (TIM3_CH4)
+
+  - STM32100E-EVAL, STM32100B-EVAL, STM3210E-EVAL and STM3210B-EVAL Set-up 
+    - Connect the following pins to an oscilloscope to monitor the different 
+      waveforms:
+       - PC.06
+       - PA.06 (TIM3_CH1)
+       - PA.07 (TIM3_CH2)
+       - PB.00 (TIM3_CH3)
+       - PB.01 (TIM3_CH4)
+  
+@par How to use it ? 
+
+In order to make the program work, you must do the following :
+ - Copy all source files from this example folder to the template folder under
+   Project\STM32F10x_StdPeriph_Template
+ - Open your preferred toolchain 
+ - Rebuild all files and load your image into target memory
+ - Run the example
+
+@note
+ - Low-density Value line devices are STM32F100xx microcontrollers where the 
+   Flash memory density ranges between 16 and 32 Kbytes.
+ - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
+ - Medium-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 64 and 128 Kbytes.  
+ - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
+ - High-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.
+ - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.
+ - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 512 and 1024 Kbytes.
+ - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
+   
+ * <h3><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h3>
+ */