--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/libs/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/ADC/3ADCs_DMA/readme.txt	Mon Oct 03 21:19:15 2011 +1030
@@ -0,0 +1,94 @@
+/**
+  @page ADC_3ADCs_DMA 3 ADCs DMA example
+  
+  @verbatim
+  ******************** (C) COPYRIGHT 2011 STMicroelectronics *******************
+  * @file    ADC/3ADCs_DMA/readme.txt 
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    08-April-2011
+  * @brief   Description of the 3ADCs DMA example.
+  ******************************************************************************
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  ******************************************************************************
+   @endverbatim
+
+@par Example Description 
+
+This example describes how to use the 3 ADCs in independent conversions. 
+Two of them; ADC1 and ADC3 are transferring continuously converted data using DMA
+while ADC2 converted data are stored using End of conversion interrupt.
+
+ADC1 is configured to convert continuously ADC channel14. Each time an end of
+conversion occurs the DMA1 transfers, in circular mode, the converted data from 
+ADC1 DR register to the ADC1_ConvertedValue variable.
+
+ADC2 is configured to convert continuously ADC channel13. Each time an end of
+conversion occurs an end of conversion interrupt is generated and inside the
+interrupt routine the converted data are read from ADC2 DR register and stored
+into the ADC2_ConvertedValue variable.
+
+ADC3 is configured to convert continuously ADC channel12. Each time an end of
+conversion occurs the DMA2 transfers, in circular mode, the converted data from
+ADC3 DR register to the ADC3_ConvertedValue variable.
+
+The ADCs clocks are set to 14 MHz.
+
+The result of ADC1, ADC2 and ADC3 conversion is monitored through the three
+variables: ADC1ConvertedValue, ADC2ConvertedValue and ADC3ConvertedValue.
+
+@par Directory contents 
+
+  - ADC/3ADCs_DMA/stm32f10x_conf.h    Library Configuration file
+  - ADC/3ADCs_DMA/stm32f10x_it.c      Interrupt handlers
+  - ADC/3ADCs_DMA/stm32f10x_it.h      Interrupt handlers header file
+  - ADC/3ADCs_DMA/system_stm32f10x.c  STM32F10x system source file
+  - ADC/3ADCs_DMA/main.c              Main program
+
+@par Hardware and Software environment 
+
+  - This example runs only on STM32F10x High-Density and XL-Density Devices.
+  
+  - This example has been tested with STMicroelectronics STM3210E-EVAL (High-Density
+    and XL-Density) evaluation board and can be easily tailored to any other 
+    supported device and development board.
+
+  - STM3210E-EVAL Set-up 
+    - Connect a variable power supply 0-3.3V to ADC3 Channel12 mapped on pin PC.02
+    - Connect a variable power supply 0-3.3V to ADC2 Channel13 mapped on pin PC.03
+    - Connect a variable power supply 0-3.3V to ADC1 Channel14 mapped on pin PC.04
+      (potentiometer RV1 on STM3210E-EVAL board)
+      
+@par How to use it ? 
+
+In order to make the program work, you must do the following :
+ - Copy all source files from this example folder to the template folder under
+   Project\STM32F10x_StdPeriph_Template
+ - Open your preferred toolchain 
+ - Rebuild all files and load your image into target memory
+ - Run the example 
+
+@note
+ - Low-density Value line devices are STM32F100xx microcontrollers where the 
+   Flash memory density ranges between 16 and 32 Kbytes.
+ - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
+ - Medium-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 64 and 128 Kbytes.  
+ - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
+   microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
+ - High-density Value line devices are STM32F100xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.  
+ - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 256 and 512 Kbytes.
+ - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
+   the Flash memory density ranges between 512 and 1024 Kbytes.
+ - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
+    
+ * <h3><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h3>
+ */