Mercurial > ~darius > hgwebdir.cgi > stm32temp
comparison libs/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/PWR/STANDBY/readme.txt @ 0:c59513fd84fb
Initial commit of STM32 test code.
author | Daniel O'Connor <darius@dons.net.au> |
---|---|
date | Mon, 03 Oct 2011 21:19:15 +1030 |
parents | |
children |
comparison
equal
deleted
inserted
replaced
-1:000000000000 | 0:c59513fd84fb |
---|---|
1 /** | |
2 @page PWR_STANDBY PWR STANDBY example | |
3 | |
4 @verbatim | |
5 ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* | |
6 * @file PWR/STANDBY/readme.txt | |
7 * @author MCD Application Team | |
8 * @version V3.5.0 | |
9 * @date 08-April-2011 | |
10 * @brief Description of the PWR STANDBY example. | |
11 ****************************************************************************** | |
12 * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS | |
13 * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE | |
14 * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY | |
15 * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING | |
16 * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE | |
17 * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. | |
18 ****************************************************************************** | |
19 @endverbatim | |
20 | |
21 @par Example Description | |
22 | |
23 This example shows how to enters the system to STANDBY mode and wake-up from this | |
24 mode using: external RESET, RTC Alarm or WKUP pin. | |
25 | |
26 In the associated software, the system clock is set to 24 MHz on Value line devices | |
27 and to 72 MHz on other devices using the external high speed oscillator(HSE), an EXTI line | |
28 is configured to generate an interrupt on falling edge and the SysTick is programmed | |
29 to generate an interrupt each 250 ms. In the SysTick interrupt handler, the LED1 is | |
30 toggled, this is used to indicate whether the MCU is in STANDBY or RUN mode. | |
31 | |
32 When a falling edge is detected on the EXTI line an interrupt is generated. In the | |
33 EXTI handler routine the RTC is configured to generate an Alarm event in 3 second | |
34 then the system enters STANDBY mode causing the LED1 to stop toggling. | |
35 A rising edge on WKUP pin or an external RESET will wake-up the system from | |
36 STANDBY. If within 3 second neither rising edge on WKUP pin nor external RESET | |
37 are generated, the RTC Alarm will wake-up the system. | |
38 | |
39 After wake-up from STANDBY mode, program execution restarts in the same way as after | |
40 a RESET, the LED1 restarts toggling, LED2 is turned on and the RTC configuration | |
41 (clock source, enable, prescaler,...) is kept. | |
42 As result there is no need to configure the RTC. | |
43 | |
44 Two leds LED1 and LED2 are used to monitor the system state as following: | |
45 - LED1 toggling: system in RUN mode | |
46 - LED1 off / LED2 off: system in STANDBY mode | |
47 - LED2 on: system resumed from STANDBY mode | |
48 | |
49 @par Directory contents | |
50 | |
51 - PWR/STANDBY/stm32f10x_conf.h Library Configuration file | |
52 - PWR/STANDBY/stm32f10x_it.c Interrupt handlers | |
53 - PWR/STANDBY/stm32f10x_it.h Header for stm32f10x_it.c | |
54 - PWR/STANDBY/main.c Main program | |
55 - PWR/STANDBY/system_stm32f10x.c STM32F10x system source file | |
56 | |
57 @par Hardware and Software environment | |
58 | |
59 - This example runs on STM32F10x Connectivity line, High-Density, High-Density | |
60 Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density | |
61 and Low-Density Value line Devices. | |
62 | |
63 - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density | |
64 Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), | |
65 STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) | |
66 evaluation boards and can be easily tailored to any other supported device | |
67 and development board. | |
68 To select the STMicroelectronics evaluation board used to run the example, | |
69 uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL) | |
70 | |
71 - STM32100E-EVAL Set-up | |
72 - Use LED1 and LED2 connected respectively to PF.06 and PF.07 pins | |
73 - Use the Key push-button connected to pin PG.08 (EXTI Line8). | |
74 - Use the Wakeup push-button connected to WKUP(PA.00) pin | |
75 | |
76 - STM32100B-EVAL Set-up | |
77 - Use LED1 and LED2 connected respectively to PC.06 and PC.07 pins | |
78 - Use the Key push-button connected to pin PB.09 (EXTI Line9). | |
79 - Use the Wakeup push-button connected to WKUP(PA.00) pin | |
80 | |
81 - STM3210C-EVAL Set-up | |
82 - Use LED1 and LED2 connected respectively to PD.07 and PD.13 pins | |
83 - Use the Key push-button connected to pin PB.09 (EXTI Line9). | |
84 - Use the Wakeup push-button connected to WKUP(PA.00) pin, make sure | |
85 that jumper JP14 is in position 2-3. | |
86 | |
87 - STM3210E-EVAL Set-up | |
88 - Use LED1 and LED2 connected respectively to PF.06 and PF.07 pins | |
89 - Use the Key push-button connected to pin PG.08 (EXTI Line8). | |
90 - Use the Wakeup push-button connected to WKUP(PA.00) pin | |
91 @note the jumper JP4 must be not fit to be able to use the Wakeup push-button | |
92 | |
93 - STM3210B-EVAL Set-up | |
94 - Use LED1 and LED2 connected respectively to PC.06 and PC.07 pins | |
95 - Use the Key push-button connected to pin PB.09 (EXTI Line9). | |
96 - Use the Wakeup push-button connected to WKUP(PA.00) pin | |
97 | |
98 @note For power consumption measurement in STANDBY mode, you have to replace | |
99 jumper JP9 in the STM3210B-EVAL board, JP12 in the STM3210E-EVAL or | |
100 JP23 (position 1-2) in the STM3210C-EVAL board by an amperemeter. | |
101 | |
102 | |
103 @par How to use it ? | |
104 | |
105 In order to make the program work, you must do the following : | |
106 - Copy all source files from this example folder to the template folder under | |
107 Project\STM32F10x_StdPeriph_Template | |
108 - Open your preferred toolchain | |
109 - Rebuild all files and load your image into target memory | |
110 - Run the example in standalone mode (without debugger connection) | |
111 | |
112 @note | |
113 - Low-density Value line devices are STM32F100xx microcontrollers where the | |
114 Flash memory density ranges between 16 and 32 Kbytes. | |
115 - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx | |
116 microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. | |
117 - Medium-density Value line devices are STM32F100xx microcontrollers where | |
118 the Flash memory density ranges between 64 and 128 Kbytes. | |
119 - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx | |
120 microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. | |
121 - High-density Value line devices are STM32F100xx microcontrollers where | |
122 the Flash memory density ranges between 256 and 512 Kbytes. | |
123 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where | |
124 the Flash memory density ranges between 256 and 512 Kbytes. | |
125 - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where | |
126 the Flash memory density ranges between 512 and 1024 Kbytes. | |
127 - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. | |
128 | |
129 * <h3><center>© COPYRIGHT 2011 STMicroelectronics</center></h3> | |
130 */ |